一 . ST推出系列Three-Phase controller with MCU STSPIN32F0 Series产品.共有7款,其中:
- 工作电压低于45Vdc STSPIN32F0 共3款。
该stspin32f0是一种Combo IC. 提供了适合于使用不同驱动模式驱动三相BLDC电机的集成解决方案。 它嵌入了一个三重半桥门驱动器,能够驱动功率MOSFET或IGBT,电流能力为600mA。 由于集成联锁功能,同一半桥的高、低侧开关不能同时驱动高。 内部DC/DCBUCK转换器提供3.3V电压,适合于同时提供MCU和外部组件。 内部LDO线性调节器为栅极驱动器提供电源电压。3款主要的区别在于:
- STSPIN32F025X( 包含1&2,共2款High Voltage rail up to 250V,主要区别在于Driver Current大小不同),系统是一个非常集成的解决方案,用于驱动三相应用,帮助设计师减少PCB面积和整体材料清单。 它嵌入了一个stm32f031x6x7和一个250v三重半桥门驱动器,能够驱动功率MOSFET或IGBTS。 集成了一种具有先进Smartsd功能的比较器,确保了对过载和过流的快速有效保护。 集成高压自举二极管,以及在下驱动段和上驱动段的抗交叉传导、死区和UVLO保护,这防止了电源开关在低效率或危险条件下工作。 匹配的延迟之间的低和高侧部分保证没有周期失真。 集成MCU允许执行foc、6步无传感器和其他先进的驱动算法,包括速度控制回路.
3.STSPIN32F060X(包含1&2,共2款High Voltage rail up to 600V,主要区别在于Driver Current大小不同), 系统包是一个非常集成的解决方案,用于驱动三相应用, 它嵌入了一个stm32f031x6x7和一个600v三重半桥 门驱动器,能够驱动高压功率MOSFET或IGBTS。 集成了一种具有先进Smartsd功能的比较器,确保了对过载和过流的快速有效保护。 高压自举二极管也是集成的,以及在下驱动段和上驱动段的抗交叉传导、死区和 UVLO保护,这防止了电源开关在低效率或危险条件下工作。 匹配的延迟之间的低和高侧部分保证没有周期失真。 集成MCU允许执行foc、6步无传感器和其他先进的驱动算法,包括速度控制回路.
二 . 在上述IC的基础上,ST又推出新的STSPIN32G4 产品。与上述IC比较,不同之处见下面几点:
- STSPIN32G4 与STSPIN32F0最主要的区别在于:
- MCU 由Cortex M0核升级到Cortex M4;工作频率,Flash,SRAM都有大的提升;
- Comparators / Op-Amp 数量增多,为研发者设计提供各种保护的可能;
- Bus Wire Voltage 提高,拓宽STSPIN32G4 应用领域;Key Applications: Industrial automation /Robotics /Battery Powered home Appliances /Power Tools /Drones /Aeromodelling /Fans & Pumps.
- STSPIN32G4 Block diagram及 some units 基本性能:
Block基本等同与STSPIN32F0,微有区别
- MCU 核由ARM Cortex-M4 替代Cortex M0;
- OP-Amps / Comparator 数量有所增多;
- 输出端还增加 SCREF PIN ,用来监控后端开关管正常工作状况;
- MCU Mainstream ARM Cortex M4
- 128K bytes of flash;
- 32K bytes RAM;
- 170MHz CPU;
- 4X USART
- Timers
- 2X 16bit ADCs
- 4X 12bit DACs
- I/F
- 7~3.6V Supply.
- 3V LDO linear regulator up to 150mA/ 0.5 W;
- Vcc buck converter up to 200mA;
- Desat(SCREF) pin: ref V (0.2v~2.5v) for embedded short-circuit protection which monitors external MOS Vds : VDSth=VSCREF;
- 4X Fast comparators(td<35ns);
- 3X rail-to-rail OP-AMPs (15MHZ bandwidth);
- 32GPIOS (ADC input & I2C or SPI or USART interface)
- 3Phase GD / VCC Buck regulator /3.3v LDO Characteristics:
Triple half-bridge driver:
- I Sink /Source up to 1A;
- Bootstrap Diodes embedded;
- Interlocking feature;
- UVLO & OTP with Fault feedback;
- In-Out prop delay=120ns;
Vcc Buck regulator embedded:
- V supply for GD;
- Programmable output Voltage (8V-10V-12V-15V);
- UVLO & OTP;
3.3V LDO Reg embedded:
- MCU V supply(available externally);
- OCP, SC, UVLO & OTP;
- 3.3V LDO Linear Regulator:
- Input supply voltage: VM=5.5~75V;
- Provide the 3.3V suitable to supply the integrated MCU and other external device;
- A soft-start function with fixed start-up time to minimize inrush current at Start-up;
- Overcurrent and short-circuit protection;
- UVLO Protection;
- Thermal Protection.
- Note: REG Pins can be shorted together providing the MCU supply externally.
- Vcc Buck Regulator:
- Input supply voltage: VM=5.5~75V;
- Provide the Vcc supply voltage for gate drivers section , Programmable output Voltage: 8V- 10V-12V-15V;
- UVLO Protection
- Thermal protection
- Note: It is possible to provide externally the Vcc supply bypassing the integrated regulator.
- STSPIN32G4 Standby Regulator:
- The device enters in low consumption mode setting the STBY bit;
- All the outputs driver forced low (external power switches turned off);
- All the embedded protections are disabled;
- The buck regulator is disabled;
- The 3.3V LDO linear regulator is switched off
- The I2C communication is not available;
评论